![]() Basically, you can run 2 MoCA networks, but throughput will align closer to bonded MoCA 2.0 rather than MoCA 2.5. The MoCA specification further details categories of devices. Because MoCA encapsulates the Ethernet frame from one end of the MoCA network to the other, the bridge is invisible to the connected Ethernet device. Note that the dual MoCA networks must share the MoCA spectrum, so the throughput for each MoCA 2.5 network is reduced from the theoretical maximum based on how many channels are employed for the link, with each channel offering up to 400 Mbps shared throughput. interfacing device, such as a MoCA Coaxial-to-RJ45 bridge. So retail adapters *could* be used provided they are configured in sync with (not overlapping) whatever setting is chosen for the FCA251 MoCA WAN link, “LAN” or “WAN.”Įdit: p.s. However odd, this setup would require two MoCA adapters at your router location, one bridging your WAN connection from the ONT, and the 2nd bridging your router LAN over your coax.Ĭan you report back with the current configuration toggle setting for your WAN FCA251 adapters?įWIW, here’s the operating frequencies for each setting, copied from a goCoax forum thread (which was taken from the FCA251 user guide): (Can't isolate the modem feed if looking to use the gateway built-in MoCA bridge.) That said, the XB6 MoCA spec is pretty old, possibly just standard/unbonded MoCA 2.0, so I recommend disabling it in favor of using a MoCA 2.5 adapter as the main MoCA/Ethernet bridge (effectively the MoCA access point). Yes, but because your WAN connection is over MoCA via the FCA251 adapters, you’ll likely need to use FCA251 adapters (with the configuration switch toggled to a compatible setting), rather than retail adapters, to effect two MoCA networks over the same coax. Think of MoCA as a no new wires technology as it uses the existing coaxial cables already in most people’s homes. ![]() However, this time I try to use these 2 adapters but it did not work. Find low everyday prices and buy online for delivery or in-store pick-up. A remote MoCA adapter connected to the coax segment and to an Ethernet client device. I bought Hitron & ScreenBeam Moca adapters in other rooms to build a Moca LAN and there are no problems. Shop ScreenBeam MoCA 2.5 Network Adapter for Ethernet Over Coax (2 Pack) 2.5 GBPS Coax to 1.0 GBPS Ethernet Adapter Black at Best Buy. A MoCA node connected to the router LAN and to the coax segment, to bridge between the coax/MoCA and Ethernet LAN this MoCA node could be a standalone MoCA adapter or a coax-equipped gateway with built-in MoCA bridging. 2.5Gbps Ethernet port to support wired speeds greater than 2 Gbps. ![]() Can I get additional Moca adapter, so I can convert all of the rooms pre-wired coax wiring to ethernet connection, then I can use ethernet cables to connect to my computer ? In another words, I don't need to use wireless connection in other rooms?īefore Frontier, I used Spectrum internet service. I use the Aris in bridge mode and use an Orbi RBR50 for my router with one satellite. I have another 3 rooms, and all of the rooms has pre-wired coax cable. My question is: can I build a Moca LAN? Currently the router is in my study room. In my study room, coax cable from my wall Jack connect to another Frontier Moca adapter, and then use ethernet cable from the other end of the Moca adapter to router WAN port. The ONT box is located outside the house, and the technician put a Frontier FCA251 MoCA adapter in the ONT. A package that one person has is not always available to everyone else.Currently I have Frontier fiber internet, and use coax connection. Please feel free to downvote otherwise misinformation and/or blatant lie's.ĭO NOT post about how people should switch from Verizon unless the original thread requests ideas for reducing costs or changing carriers.ĭO NOT post about how to get illegal services running on Verizon's network.īundle prices and offers cannot be quoted by anyone other than a rep who is actually at work in front of their computer. DO Report any spam you find, to the moderators.ĭO Search for duplicate entries before posting redundant threads.ĭO NOT post any personal confidential information.ĭO NOT downvote an otherwise acceptable post or comment, just because you disagree with it. Summing up everything from this thread into one post to mark as 'best answer': The 'IP HD Network Coaxial Transmission Extender' device did not work for converting a coax signal to ethernet because it did not have a Type F Coax connector, which is what the port in my wall uses.I instead bought a MoCA 1.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |